Mycube Touch
Mycube Touch / Setting up your safe / Setup /

Setup

Please click the link below to view an instructional video on setting up your safe:

Mycube Touch Setup

You can also refer to the step by steps instructions below:

  1. Open the door, press **01#.
  2. You will hear “please enter your password.”
  3. Enter a 4-6 digit password and press #, you will hear "please do again."
  4. Re-enter your password and press #.
  5. You can now proceed with setting your biometric fingerprint

Mycube Touch / Setting up your safe / Setup /

Fingerprint Registration

Please click the link below to view an instructional video on setting up your fingerprint:

Mycube Touch Fingerprint Setup

You can also refer to the step by steps instructions below:

You must register your 4-6 digit passcode before completing fingerprint registration.

  1. Open the door, press **02#, you will hear “Please verify.”
  2. Enter your password and press #.
  3. After verification you will hear “Please put your finger on scan sensor”
  4. Then you will hear “Please do again” twice.
  5. When your fingerprint registration is completed successfully, you will hear “Fingerprint registration complete.”
  6. If verification fails, you will hear “verification failed”, system will quit. Please restart the process.

*Note: If there's any issue with the fingerprint while registering it for first time, clear the safe, by pressing *. Then place the middle of your fingerprint on the sensor first. Rotate slightly to the right side, then rotate slightly to the left side so that the sensor captures the full fingerprint with the three reads. *

Mycube Touch / Setting up your safe / Setup /

Installation

Please click the link below to view an instructional video on installing your safe:

Installing Your Safe

Please click the following link for an instructional video on removing your keyhole cover:

Removing Keyhole Cover

Mycube Touch / Setting up your safe / Setup /

Registration

To register your Mycube safe please click the link below:

Register Your Safe

Mycube Touch / Setting up your safe / Setup /

Opening and Closing Your Safe

Refer to the instructions below to open & close your safe

  1. Open the Door
  2. Enter your password and press #, or place your registered finger, you will hear “verification complete.”
  3. If the password or fingerprint is not right, you will hear “verification failed.”
  4. If the wrong password has been entered 3 times in a row, the keyboard will be locked for 5 minutes.
  5. If the wrong fingerprint has been placed 5 times in a row, the scanner will be locked for 5 minutes.
  6. Close the Door
  7. Press # to lock.

Mycube Touch / Setting up your safe / Setup /

Resetting Your Code

Refer to the instructions below to reset your code:

Mycube Touch Reset Code

You can also refer to the instructions below:

  1. Open the door, press ** and the current password and press #. You will hear “please enter new password”
  2. Enter the new password and press #, you will hear “please do again”
  3. Re-enter your password and press #.
  4. Your password change is complete!

Mycube Touch / Setting up your safe / Setup /

Resetting Your Safe

Refer to the instructions below to reset your safe:

  1. Open the door, press **999#, you will hear “please verify.”
  2. Enter your password or registration fingerprint and press #.
  3. You will hear “reset complete.”

Mycube Touch / Setting up your safe / Setup /

Volume Adjustment

Refer to the steps below to adjust your volume:

  1. Open the door and press **03# (*The keyboard only shows 2, 8, *, #)
  2. Press 2 - To turn up the volume
  3. Press 8 - To turn down the volume
  4. Press * To quit without saving
  5. Press # - To save and quit

Mycube Touch / Setting up your safe / Setup /

Clearing An Entry

If you input an incorrect digit, press * to clear the keypad.

Mycube Touch / Setting up your safe / Setup /

Operational Manual

Mycube Touch Operational Manual

Download PDF