MyCube Homepage

Please click the link below to view an instructional video on setting up your safe:

Setting Up Your Safe

Please click the link below to view an instructional video on installing your safe:

Installing Your Safe

The following link is an illustration of the installation process:

Installing Your Safe Illustration

Register Your Safe

Please refer to the instructions below to open and close your safe:

1. To open the safe enter your 4-digit code.
2. To lock, close the door and press LOCK.

Please click the link below to view an instructional video on resetting your passcode:

Resetting Your Code

You can also refer to the instructions below

1. Open your door using the existing passcode or manual key.
2. Press CLEAR twice.
3. PROG will appear on the screen.
4. Input 68, then press LOCK.
5. NEU will appear on the screen.
6. Input your 4 digit code and press LOCK.

If you are unable to successfully reset your code, try the process with your manual key inserted in the safe.

1. Insert the manual key and close the safe door
2. Press CLEAR 2x, “PROG” will appear on the screen
3. Press 68 LOCK, “NEU” will appear on the screen
4. Press your 4-digit code, and press LOCK*. Your code is now set.

Note: Apply a little pressure to ensure that the door is closed securely after pressing LOCK, once it is locked, you can remove the key.

E-code means "error code". This error will appear if you are typing in the incorrect code. If you can't remember your code, use your manual key to open the safe then reset your code. Refer to the following video for instructions on resetting your code:

Resetting Your Code

If the batteries have corroded, use white vinegar and Q-tip to clean off the coils. Once coils are clean install 4AA batteries.

If that doesn't work, you will need a replacement battery pack. Please send an email to support@mycubesafe.com and a member from our Customer Service Team will contact you to provide further assistance.

Error 1 appears when you have entered the wrong code. Retry code entry using the correct code. If you forgot refer to the instructions below.

With Manual Key

If you forgot your code and have your manual key, please click the link below to view an instructional video on opening your safe using your safe key:

Using Your Manual Key

Refer to the link below for an instructional video on resetting your passcode:

Resetting Your Code

Without Manual Key

If you forgot your code and do not have your manual key, please send an email to support@mycubesafe.com and a member from our Customer Service Team will contact you to provide further assistance.

If the Error 2 code appears, make sure the bolts are not getting jammed. Try to lock the safe with the door swung open. If this works, then try removing the little square rubber pieces on the inside of the door frame to resolve the error. If that does not resolve the issue, send an email to support@mycubesafe.com and a member from our Customer Service Team will contact you to provide further assistance.

The Batt-Hi message appears when the safe is already locked and Lock is pressed. If the safe looks open and pressing Lock still gives Batt-Hi message, use manual the key to fully open the safe.

Please click the link below to view an instructional video on opening your safe using your safe key:

Using Your Manual Key

If you are setting up your safe for the first time and press Lock and it locks the safe before you have set a code, try using the factory default code 1234 to open the safe. If that does not work, open the safe with the manual key. If you are still unable to open the safe, please send an email to support@mycubesafe.com and a member from our Customer Service Team will contact you to provide further assistance.

When locking the safe, keep the door held closed until after you have pressed Lock. Wait for 1 second after the LED screen says "CLOSED", otherwise the door will spring open and the bolts will jam. If the bolts jam, you can insert the manual key to unjam the bolts.

When setting up your code, PROG should appear on the keypad. If you don't see "PROG" on the screen, this means that your safe is locked - even if it doesn't appear to be. When the safe is in the locked position, you will not be able to program/reset your code. In order to correct this, use your manual key that came with the safe to unlock the safe. Remove the keyhole cover with Mycube logo to unlock the safe, and leave the key in the door. Then proceed with programming/resetting your code until you see PROG appear and you go through the steps. Once the safe is programmed and back in the locked position, you can remove the manual key and place the keyhole cover back on the keypad.

Every safe come with an accessory pack which contains a set of 4 AA batteries, wrenches and a set of keys. Please keep your manual keys and wrenches outside of your safe for easy access in the event that you get locked out of your safe or need to change the batteries.

Replace your safe's batteries every 12 months for optimal performance. Please click the link below to view an instructional video on replacing your safe batteries:

Replacing Your Batteries